TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is really a new pen that was created by two guys in California. They wanted to create a cool writing instrument that looked like a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.
The Smok Pen has a built quality that is just great. I found that even though it can be an electronic pen the construction is simply as good as the pens that I have reviewed. It is because of how they made the top cap. You don’t have to worry about the cap cracking or breaking you Smok Valve Pen.
Both biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. In general the coil on a Smok Pen is bigger than on other pens. I believe that they did this deliberately, to make the pen feel bigger.
Invest the a look at a Smok Pen, you will notice that your body of the pen is round and not smooth like other pens. On the back of the pen there exists a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I really liked this feature because it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen you should keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature you can switch off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
When you put your Smok Pen into the tank you will notice a indicator light come on. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. You should always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.
Once you have completed this step, you should always check to see in case you are at the right temperature for the coils to fire. If not then you should turn the power off and try again. When you are still not satisfied with your Smok Pen then I suggest you take it set for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.
Prior to going any further you should remove the battery from your pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. After you have loosened this wire after that you can access the sub-ohm. You should then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.
When you have placed the sub-ohm tank in to the pen you need to then place all of those other components including the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. EightVape When you initially put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it requires to reach you should then connect both wires to the negative and positive on the positive post on the Smok unit. You need to then connect the other end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to underneath of the Smok’s power switch.
After all of the components have been placed into the pen, you should turn the power on. After the first test run, you have to be able to start to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you need to take away the battery from the pen and then replace it with a brand new one. For your convenience there is also a green light which can be pressed to be able to confirm the battery charging status. Once you have done these things and you do not start to see the green light indicating charging, you should replace the battery.